############# POLY Example 1 #############
VERSION 1 # Currently, this should only be 1.

###### DEFINITIONS

# Names support all alphanumeric ASCII, and ' ', '_', '-', '+'
# Can also be omitted or NULL to not override the current track name, e.g. "TRACKNAME NULL"
TRACKNAME CircuitT_Synth1

# Can be POLY, DRUM, MPE, or NULL
TYPE POLY

# Can be A, B, C, D, USBD, USBH, CVGx (x between 1&4), CVx, Gx, or NULL
OUTPORT NULL

# Can be x (between 1-16), or NULL -- this is ignored if output port is not MIDI
OUTCHAN 1

# Can be NONE, ALLACTIVE, A, B, USBH, USBD, CVG, or NULL
INPORT ALLACTIVE

# Can be x (between 1-16), ALL, or NULL -- ignored if INPORT is NONE, ALLACTIVE or CVG
INCHAN ALL

# This defines the default 'MAX RATE' for automation lanes.
# Can be NULL, 192, 96, 64, 48, 32, 24, 16, 12, 8, 6, 4, 3, 2, 1
MAXRATE NULL

# PC
# Syntax: NUMBER NAME
# number must be either:
#   - A number (for simple PC)
#   - Three numbers, delimited by ':', which represent PC:MSB:LSB. You can put 'NULL' to not set the MSB/LSB.
# PC must be between 1...128
# MSB/LSB must be between 0...127
[PC]
[/PC]

# CC
# Syntax: CC_NUMBER NAME or CC_NUMBER:DEFAULT=xx NAME
# DEFAULT_VALUE must be a valid number between 0 and 127
[CC]
19 Osc1 wave
20 Osc1 wave interp
21 Osc1 PW
22 Osc1 Vsync
24 Osc1 Density
25 Osc1 Den. Detune
26 Osc1 Semitones
27 Osc1 Cents
28 Osc1 Pitchbend

29 Osc2 wave
30 Osc2 wave interp
31 Osc2 PW
33 Osc2 Vsync
35 Osc2 Density
36 Osc2 Den. Detune
37 Osc2 Semitones
39 Osc2 Cents
40 Osc2 Pitchbend

51 Osc1 Level
52 Osc2 Level
54 Ringmod Level
56 Noise level
58 prefx level
59 postfx level

60 filter routing
63 filter drive
63 filter drive type
68 filter type
74 filter frequency
69 filter tracking
71 filter resonance
78 filter q normalize
79 filter env2 to frequency

108 env1 velocity
73 env1 attack
75 env1 decay
70 env1 sustain
72 env1 release

91 Distortion level
93 chorus level

80 macro1
81 macro2
82 macro3
83 macro4
84 macro5
85 macro6
86 macro7
87 macro8
[/CC]

# NRPN
# Syntax: "MSB:LSB:DEPTH NAME" or "MSB:LSB:DEPTH:DEFAULT=xx NAME"
# Lsb & msb should be between 0 and 127
  # Note: LSB can be over 127 ONLY if MSB is 0 or omitted
  # e.g. '0:1026:7 FOO', or ':2000:7 BAR' 
  # the examples above would be equivalent to '8:2:7 FOO' and '15:80:7 BAR' respectively
# DEPTH can be 7 or 14
# For NRPN: DEFAULT_VALUE must be a valid number, either between 0 and 127 (for 7 bit NRPNs) or between 0 and 16383 (for 14bit NRPNs)
[NRPN]
0:0:7 Env2 velocity
0:1:7 Env2 Attack
0:2:7 Env2 Decay
0:3:7 Env2 Sustain
0:4:7 Env2 Release
[/NRPN]


# This section will be readable from Hapax.
[COMMENT]
Not exhaustive, a lot is there already.
All info from the Circuit Programmers Reference Guide.
[/COMMENT]